Latest Products
RFD900X 915MHz Ultra 40km Long Range Telemetry Radio Modem with Antenna for APM PIX Flight Controller
Features
The RFD900x is a high performance 900MHz, ISM band radio modem covering the 902 – 928 MHz frequency band. It is designed for long range serial communications applications requiring best in class radio link performance.
Product Details
New Features for the X series:
New Processor, ARM 32 bit core.
Air data rate: 500kbit/s.
AES Hardware accelerated encryption. *Fully working*
RC PPM Passthrough with telemetry at the same time.
GPIO Pin Mirroring – see datasheet for more.
Original SiK point to point firmware implemented.
Asynchronous multipoint firmware, *Beta release*
Key Features:
Long range >40km depending on antennas and GCS setup
2 x RP-SMA RF connectors, diversity switched.
1 Watt (+30dBm) transmit power.
Transmit low pass filter.
> 20dB Low noise amplifier, high IP3.
RX SAW filter.
Passive front end band pass filter.
Fully ESD protected + filtered – Every IO port is protected and filtered.
Re implemented SiK and Multipoint SiK firmware, field upgradeable, easy to configure.
Small, light weight.
License free use in Australia, Canada, USA, NZ.
Note: Not air-compatible with older “+” series modems with current software.
Compliance:
The RFD900 is designed to be compliant with the following standards:
FCC Part 15.247 (Frequency hopping and digitally modulated intentional radiators)
AS/NZS 4268:2012 (Radio equipment and systems – short range devices)
Specifications:
Frequency Range: 902 – 928 MHz (USA) / 915 – 928 MHz (Australia) / 868 – 870 (European Band)
Output Power: 1W (+30dBm), controllable in 1dB steps ( +/- 1dB @ <20dBm, +/- 0.5dB >=20dBm typical )
Air Data transfer rates: 4, 64, 128, 250, 500 kbit/sec ( 64k/128k default )
UART data transfer rates: 2400, 4800, 9600, 19200, 38400, 57600, 115200 baud , and higher. ( 57600/115200 default )
Receive Sensitivity: >121 dBm at low data rates, high data rates (TBA)
Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) – Including RF Shield, Heatsink and connector extremities
Weight: 14.5g
Mounting: 3 x M2.5 screws, 3 x header pin solder points
Power Supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~800 mA peak at maximum power
Temp. Range: -40 to +85 deg C, tested operational from -73 to +123 deg C.
Interfaces:
RF : 2 x RP-SMA antenna connectors – it is OK to have only one antenna connected
Serial: Logic level RS232 (+3.3v nominal, +5v tolerant)
Power: +5v, ~800mA max peak (at maximum transmit power)
GPIO: 6 General purpose IO (Digital, ADC, PWM capable).
The following cable from FTDI is compatible with the RFD900 modem. Pin 1 of the FTDI cable connects to Pin 1 of the RFD900 header.
To power the modem from the +5V USB power, a jumper is needed between pins 4 and 6.
To power the modem from an external +5V supply, connect power to pins 2 and 4.
Your Purchase Includes:
RFD900x Modem Telemetry x 1 set
Features
The RFD900x is a high performance 900MHz, ISM band radio modem covering the 902 – 928 MHz frequency band. It is designed for long range serial communications applications requiring best in class radio link performance.
Product Details
New Features for the X series:
New Processor, ARM 32 bit core.
Air data rate: 500kbit/s.
AES Hardware accelerated encryption. *Fully working*
RC PPM Passthrough with telemetry at the same time.
GPIO Pin Mirroring – see datasheet for more.
Original SiK point to point firmware implemented.
Asynchronous multipoint firmware, *Beta release*
Key Features:
Long range >40km depending on antennas and GCS setup
2 x RP-SMA RF connectors, diversity switched.
1 Watt (+30dBm) transmit power.
Transmit low pass filter.
> 20dB Low noise amplifier, high IP3.
RX SAW filter.
Passive front end band pass filter.
Fully ESD protected + filtered – Every IO port is protected and filtered.
Re implemented SiK and Multipoint SiK firmware, field upgradeable, easy to configure.
Small, light weight.
License free use in Australia, Canada, USA, NZ.
Note: Not air-compatible with older “+” series modems with current software.
Compliance:
The RFD900 is designed to be compliant with the following standards:
FCC Part 15.247 (Frequency hopping and digitally modulated intentional radiators)
AS/NZS 4268:2012 (Radio equipment and systems – short range devices)
Specifications:
Frequency Range: 902 – 928 MHz (USA) / 915 – 928 MHz (Australia) / 868 – 870 (European Band)
Output Power: 1W (+30dBm), controllable in 1dB steps ( +/- 1dB @ <20dBm, +/- 0.5dB >=20dBm typical )
Air Data transfer rates: 4, 64, 128, 250, 500 kbit/sec ( 64k/128k default )
UART data transfer rates: 2400, 4800, 9600, 19200, 38400, 57600, 115200 baud , and higher. ( 57600/115200 default )
Receive Sensitivity: >121 dBm at low data rates, high data rates (TBA)
Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) – Including RF Shield, Heatsink and connector extremities
Weight: 14.5g
Mounting: 3 x M2.5 screws, 3 x header pin solder points
Power Supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~800 mA peak at maximum power
Temp. Range: -40 to +85 deg C, tested operational from -73 to +123 deg C.
Interfaces:
RF : 2 x RP-SMA antenna connectors – it is OK to have only one antenna connected
Serial: Logic level RS232 (+3.3v nominal, +5v tolerant)
Power: +5v, ~800mA max peak (at maximum transmit power)
GPIO: 6 General purpose IO (Digital, ADC, PWM capable).
The following cable from FTDI is compatible with the RFD900 modem. Pin 1 of the FTDI cable connects to Pin 1 of the RFD900 header.
To power the modem from the +5V USB power, a jumper is needed between pins 4 and 6.
To power the modem from an external +5V supply, connect power to pins 2 and 4.
Your Purchase Includes:
RFD900x Modem Telemetry x 1 set
RETURNS POLICY
1. Please contact us first with following information before shipping back:
-order number/contact person
-reason for returning
After confirmed with us, return instructions will be emailed to you.
2. We may require restocking fee(shipping cost) for returned merchandise without any quality problems. A re-stocking fee does not apply to defective products.
3. All merchandise returned must be packaged well to protect it from shipping damage, and must be sent with a shipping method that provides tracking information. We can not be held responsible for damage that occurs in transit.
4. For merchandise that a customer wants to return for a refund, We requires that the item and its packaging be in un-used, "like new" condition with all original packaging, cabling, manuals, etc. included, or the return will be refused. Inspect your product carefully before shipping as any signs of wear or use will result in a refused product return.
Please also include a note about your personal Info and the problems.
1.Your order number/Contact person
2.Your Detailed shipping address
3.why you have to return it?
4.what do you need us to do?
5.which part is broken?
6.Any problem you can find so far with the returned item.
SHIPPING
After order placed, you will receive a confirmation email.Once your order is shipped, you will receive tracking number and link via email.We offer express shipping , battery shipping, drone shipping to all over the world.If you have special declare value, shipping company requirment, please email us: hi@insightfpv.com
